LiitoKalaLii-500S Lii-PD4 Lii-S2 Lii-S4 lii-500 lii-PD2 lii-S8 18650 26650 1.2V 3.7V 3.2V Lithium-ion NiMH Battery Smart Charger

Description

Charger PD2. Manual.

I. Charger specifications and functions:

1. DC12V1A nominal input, two-slot independent charging and
microcomputer management system.

2. The biggest highlight of this charger is that you can charge the battery
regardless of polarity!

3. There are three levels of charging current: 0.5A / 1.0A / 2.0A. The

default charging is 0.5A. You can press and hold the corresponding
button to select the charging current.

4. During charging the LCD can display the channel CH and the

charging current, voltage, time, capacity and battery type of the channel

Li-Fe 3.20V / Li-ion 3.70V / Li-ion 3.85V IMR. The charging current of

the two slots does not exceed 2A in total. When one of the slots is

charged with 2A current, and then the battery is charged in the other

slot, the front 2A current will drop. Charge to 1A current; when the

battery is fully charged, the LCD will display FULL.

5. Automatic recognition of Li-Ion 3.70V and Ni-MH batteries, manual

selection of lithium iron phosphate battery 3.20V and Li-Ion 3.85V
battery.

6. With 0V voltage activation function, 1.65-2.20V cannot be charged

but there will be activated current trickle charging.

7. With multiple safety protection functions such as overcharge,

overdischarge, short circuit, etc., it can intelligently and automatically
identify bad batteries.

8. Charging mode: constant current and constant voltage.
II. Buttons and display:

1. Button Mode: 2 buttons each control one slot. Within 5 seconds after

the battery is powered on, click the Mode button of the corresponding

slot to select the type of rechargeable battery. Press and hold the Mode

button to select the charging current. Determine the type of battery that

needs to be charged such as 3.20V / 3.80V and stop the operation

after charging current, and enter the charging state after 5 seconds. You

cannot switch the battery type during the charging process, but you can

click the button to light up the backlight and long Press to switch the
current.

2. LCD: After the charger is connected to the power supply, the LCD

display will be displayed for about 2 seconds, and then display null.

When the battery is detected, the LCD displays the corresponding slot

number, battery voltage and current, and the battery type symbol flashes

NiMH / Nickel-cadmium 1.2V no battery type symbol blinks, after 5

seconds, it will enter the default recognition to charge the battery. At this

time, the charging display symbol flashes to indicate that charging is

in progress, and END is displayed when charging is complete.
III. Electrical technical parameters:
1. Input power: DC 12V 1A.

2.Output voltage: DC 4.20V for Li-Ion, DC 4.35V for IMR, DC 3.65V for
LiFePO4, DC 1.48V for NiMH / NI-Cd.

3. Output current optional: Li-Ion / IMR / LiFePO4: 2000mA x 1 only

one / 1000mA x 2 / 500mA x 2, NiMH / NiCd: 500mA.

4. Constant current / constant voltage charging, cut-off current: <100mA.
5. No-load standby current: <15m A.

User Manual Lii-S6

Cautions:

1.Thischarger can chargeallcylindricalrechargeablebatteries 3.7VLi-Ion,3.8VIMR,1.2VNi-MH/Cd, 3.2VLiFePO
4

2.Read this manual before use and pay special attention to the recommended charge current, must avoid to charge battery beyond the recommended current limit

3.If DC input, only12V3Ais recommended

4.Mindheating while charging

5.Remove the charger from power source after charging complete, and remove the battery from the charger at the same time

6.For indoor use only

7.The displaying dataonlyfor reference, pleaserefer to professional instrument for more accurate data

Specifications and functions:

1.Multi-powerinput: 12V 3A adapterselective,four independent charging and micro computer management system.

2.Charge current intelligent auto-set of total three levels:500mA/700mA /1000mA/2000mA，2000mAis fixed only for slot#1/3/6.

3.Multi-functionalLEDchargingindicators: forcharging progress: 25 – 50 – 75 -100,battery types: Ni-MH 1.2V , Li-Fe 3.2V, Li-ion 3.7V, Li-ion 3.80VIMR and for charging current: 0.5A/1A/2A

4.Identify Li-ion and Ni-MH batteries automatically and adjust manually the charging mode for LiFePO4 and 3.80V li-ion batteriesIMR

5.Refresh for OV battery. Itwill notcharge any battery of1.65 -2.20V refresh current can be detected only

6.Multi-safety protection function of over-charge and over-discharge,short circuited, polarity reverse and so on. It can smartly identify broken batteries with much more safety.

7.Chargingatconstant voltage and current

Button and LED :

1.Buttonof Mode: Whilepower supplyis connected, 1Short clickthemodebutton to change the battery type. It will start to charge9seconds after setting the battery type 3.2V or 3.80V, 1.2V Ni-MH and 3.7V li-ion canbe detected automatically, so it needssettingonly 3.2V and 3.8V batteries; 2 During charging process, shortclickthe mode button todisplay battery type.

Note: Battery type can be only selective before charging starts.

2.LED: Whilepower supply connected, all LEDSlight up immediately 1 If no battery isinserted,the500mAh LEDone of the three current display LEDS willkeep on and others willbe off. 2 When battery isinserted anddetected, 4 LEDcharging indicator for the channelwill beonamong which3.7Vbattery typeLED keepsflashingindicatingto set the battery type, if no operationin5 seconds, it beginsbyautomaticdetectionLi-Ion 3.7V or NIMHthenfour LEDindicatorswill display the charging status. 3During charging, short clicktheModebuttontoshow the battery typewithin5 seconds;4If nopower supplyis connected, insertinga battery, itcan quick shows the remainingchargervolumeof the battery.

x LED displaygraphic reference
:

Electrical Parameters:

1. Input : DC 12V 3A（selective）；

2. Output voltage: DC 4.2V for Li-Ion 3.70V
DC 4.35V for Li-Ion 3.85V IMR
DC 3.65V for LiFePO4
DC 1.48V for NiMH/NI-Cd

3. Output current: Li-Ion/IMR/LiFePO4 2000mA x 3only for slot#1/3/6,
1000mA x 6/700mA x 6 /500mA x 6
NiMH/NiCd: 500mA

4. Constant voltage, cut-off current: less than 100mA；
5. Standby current: less than 15mA。
Compatible battery types and sizes

Li-ion / IMR/LiFePO4: 26650，21700，20700, 18650, 18490, 18350, 17670, 17500, 16340RCR123, 14500, 10440
NiMH/Cd: AA, AAA，SC, C
lii-S6 Size and weight:

157.0mm× 149.0mm×36.5mm L x W x H
Weight: 560g
Lii-202 charger for instructions

This device is designed for portable, flexible, and several types of batteries. it can detect the battery type and charging the battery is automatically selected in accordance with the charging current. Built-in LED indicators to show charging status and 5 V / 100 mAh USB output function
warming:

this charge is only for charging the cylindrical lithium ion 3.7, 3.8, ni-mh / Ni-Cd, LiFePO4 Li-Ion batteries.

Please read these instructions before use; pay attention to the recommended charging current, never choose the wrong charging current

when charging with 5V USB AC adapter, 2A-current AC adapter recommended

Charger ma hot during operation for a long time, handle with care!

please cut off the electricity and remove the battery from the charger when charging is complete.
indoor condition only !!

data mapping Charger for reference only; please refer to the professional devices, if you need accurate data
2. Features and Specifications:

Micro USB DC 5V input, two independent slots and charging channels with built-in micro-computer control system to ensure high efficiency
Two charging current parameters 0.5A / 1.0A

Four LEDs indicate the charging status 25, 50, 75, 100, and also shows the type of battery if it is installed in the battery 1.2 V Ni-Mh, 3.2 in Li-Fe, 3.7 in Li-Ion, 3.85 in li-ion

automatically identify Li-Ion and Ni-Mh; But, you need to adjust the charging mode for LiFePO4 and 3.85 in the lithium-ion battery

it can actively 0 V battery, but the device does not charge in the 1.65 ~ 1.85 The types of batteries.

built with over-charging protection, over-discharge and reverse polarity protection. besides, it can detect a broken battery.

Charing mode: instantaneous value of current and voltage.

STANDING charging current: Operating voltage 5V-2A Micro-connector
Standard automatic 5 V / 1000 mAh USB output port
3. Select the button, LED and function.
MODE button:

select the type of battery when installing the battery. it will begin to charge the battery after fixing the battery type please note that it will automatically identify Li-Ion and Ni-Mh, no need to choose manually

Press and hold for 2 seconds, when after connecting to power, it can be switched between charging current of 0.5A and 1.0A;
led indicator

connect the charger to power, all LED indicators will be on when the battery is inserted after 5 seconds, the LED will be turned off except for the indicator 0.5A current

when the battery is inserted into the device, 4 LEDs will be turned on and 3.7 V LED is flashing, please press the MODE button to set the correct type of battery. it will begin to charge the battery after 5 seconds, and the LED indicator shows charging status.

Press the MODE button to show the type of battery 5 seconds during charging and return to show the charging status

it can show the remaining battery power, if you put the battery in the charger not connected to the charging source

USB output indicator: When the USB output is detected, the volume of the battery indicator will be on for 10 seconds and then off, press the button to display the volume rate of the battery.
4. Specification:
Input: Micro USB DC 5V / 2A

Output: 1.4, 4.2 ± 05, ± 05 3.65 ± 4.35 05
Output Current: 500/1000 mAh

constant voltage charging cut-off current: <100 mAh
Standby current: <15 mAh
5. USB output function
USB output load voltage: 4.90 V-5.30
Output Current: 1000 mAh 1A
No-load current: <1 mAh

the output voltage of 4.75 V-5.25 V, when the current 1000 mAh
output over-voltage protection: 3.0 ± 1
6. Compatibility

li-ion / IMR: 18650, 18490, 18350, 17670, 17500, 16340 RCR123, 14500, 10440
7. Size

112 mm × 60 mm × 30 mm / 86 g + 15 g USB cable
Lii-402 charger for instructions
1, the buyer attention

1. This charger can only charge cylindrical lithium ion battery 3.7V, 3.8V, nickel hydrogen / nickel cadmium, lithium iron phosphate battery;

2. Before use, please carefully refer to the instructions, pay attention to the recommended rechargeable battery charging current, do not exceed the recommended current charge;

3. Charge with a 5V USB adapter adapter current recommended 2A;

4. Charger charge and discharge may be fever, be careful not to burn;

5. When you stop using it, unplug the power and unplug the battery.
6. Can only be used in normal room.

7. This product test data is for reference only, the actual situation, please refer to professional equipment.
2, the charger requirements and functions:

1. Micro USB DC 5V input, two separate charging and microcomputer management system

2. Available for 4 kinds of charging current selection 500mA / 700mA / 1000mA / 2000mA 2000mA designated fourth slot.

3. LED display Charge status 25 50 75 100 and battery type NiMH 1.2V Li-Fe 3.2V Li-ion 3.7V Li-ion 3.85V.

4. Can automatically identify lithium Li-ion batteries and nickel-metal hydride Ni-MH batteries, manually select the iron phosphate Liepo4 battery and Li-ion 3.85V battery

5. 0V voltage activation function, 1.65-1.85V can not be charged but there will be activated current trickle type charge.

6. Have over-charge, short circuit, intelligent identification of bad batteries and reverse battery detection protection.

7. Charging mode, constant current constant pressure

8. Using DC input, the charger power supply for the 5V-2A Micro plug

9. With standard 5V / 1000mA USB automatic identification output function,
3, the key, LED and function description

1. Press the key: hold the selector key for 2 seconds to switch 500mA 700mA 1000mA 2000mA charge current at power on,

When charging the battery, press the select key to change the type of rechargeable battery. When the rechargeable battery type is selected for example, 3.20V 3.85V for 5 seconds, enter the charging state.

2. LED: charger connected to the 5V power supply, the charger all the LED moment all bright, if the battery is not put into the charging slot, 500mA LED indicator light is on, the other lights go out.

When the battery is detected, the four LED lights are all bright, 3.7LED light will flash, then press the button to select the type of battery you need to charge, if not selected, 5 seconds into the default identification of the battery charge, charge The indicator light flashes at the corresponding charge ratio. Press the button to check the charge type no power indication 5 seconds after the return to the state of charge. When not energized, insert the battery to view the power ratio 5 seconds after extinguishing, need to view again press

USB output indication: When the USB output is detected, the power indicator turns on for 10 seconds and presses to check the power.
4. LED display reference picture
4, the electrical technical parameters:
1, input power: Micro USB DC 5V / 2A
2, the output voltage: 1.42V
4.2V ± 0.05V,
3.65 ± 0.05V
4.35 ± 0.05V

3, the output current: 2000mA x 1 1000mA x 2 700mA x 3 500mA x 4

4, constant voltage charging, cut-off current: <100m A;

5, external power supply standby current: <15.0m A;
5, USB output function:

1, USB port output no-load voltage: 4.90-5.30V; specify the fourth slot for the USB output
2, the output current: 1000 m A;
3, no-load current: <1m A;

4, load 1000m A current, the port output voltage: 4.75-5.25V;

5, stop output protection voltage: 3.0 ± 0.1V;

6, compatible batteries: Li-ion / IMR: 18650, 18490, 18350, 17670, 17500, 16340 RCR123, 14500, 10440

7, charger size: 112mm × 90mm × 30mm length / width / height
Weight: g + g micro line
Lii-PL4charger for instructions
Precautions

1. This charger can handle all cylindrical batteries 3.7V Li-ion, 3.8V IMR, 1.2V Ni-MH / Cd, 3.2VLiFePO4

2. Read this manual before use and pay special attention to the recommended charging current, needs to be above the recommended current limit
3. If DC input, only 12V 1A is recommended
4. Spirit heating during loading

5. Remove the charger from power source after charging finished, and remove the battery from the charger at the same time
6. for the interior only

7. The display data for reference only, please refer to professional instrument for more accurate data
specification and function

1. Multi-power input: AC cable 110-240V 50 / 60Hz included / 12V 1A adapter selective, four independent and micro computer management system.

2. Three charging mode 500mAh / 1000mAh / 2000mAh, 2000mAh current mode is fixed only to the fourth slot.

3. The LED charging indicators: both for charging progress: 25 -50 -75 -100 and battery types: Ni-MH 1.2V, Li-Fe 3.2V, Li-ion 3.7V , Li-ion 3.80 V IMR

4. Automatically identify Li-ion and Ni-MH batteries and manually set the charging mode for LiFePO4 and 3.80V lithium ion batteries IMR

5. Upgrade for OV battery. there will be no battery of1.65-1.85V refresh current can only be detected

6. Protection for overcharge and over-discharge and short-circuit. identify broken battery and polar reverse polarity protection.
7. Charging under constant voltage and current
Button, LED and function

1. Keys: While power supply is connected, 1 Short press less than 2S to change the mode, the battery type. It will start to charge 5 seconds after the setting of the battery type 3.2V or 3, 80V, 1.2V Ni-Mh and 3.7V li-ion can be detected automatically, so it only needs adjustment of 3.2V and 3.8V batteries; 2 Change the charging current anytime during the charging process by pressing long more than 2s the mode button

2. LED: While power is plugged in, all LEDs light immediately 1 If no battery is inserted, the 500mAh LED one of the three power display LEDs will stop and others will go away. 2 When battery is inserted and detected, 4 LED charge indicator for the channel will open on taking which 3.7V battery type LED keeps flashing indicating to the battery type, if no operation in 5 seconds, it will start by automatic detection Li -Ion 3.7V or NIMH then four LED displays will show the charge status. 3 During the charging process, short-press the mode button to set the battery type within 5 seconds; 4 When no power is connected, insert a battery, it can quickly shows the remaining battery charger volume of the battery.
3. LED display graphic reference
technical specification

1. input: AC cable 110-240V 50 / 60Hz included / DC 12V 1A & # 65288; selective & # 65289;
2. Output voltage: 4.2V DC for 3.7V Li-Ion
DC 4.35 V for Li-Ion 3.8 V IMR
DC 3.65 V for LeFePO4
DC 1.48 V for NiMH / NI-Cd

3. Output current: Li-ion / IMR / LiFePO4 2000mA x 1 only for slot # 4,
1000mA x 2, 500mA x 3 500mA x 4

NiMH / NiCd: 1000mA x 2, 500mA x 3 500mA x 4

4. Constant voltage, cut-off current: less than 100mA
5. Standby current: less than 15mA
Compatible battery types and sizes

li-ion / IMR / LiFePO4: 26650 & # 65292; 21700 & # 65292; 20700, 18650, 18490, 18350, 17670, 17500, 16340 RCR123, 14500, 10440
NiMH / Cd: AA, AAA & # 65292; SC, C
size:
133mm x 100mm x 35mm L x W x H
Weight: 175g: gram including micro cable