Podofo 18 LED Car Rear View Wireless Backup Camera Kit + 7" TFT Auto LCD Monitor 12V-24V Reverse For Truck Van Caravan Trailers

Description

Podofo 7 18 LED Car Rear View Wireless Backup Camera Kit +  TFT Auto LCD Monitor 12V-24V Reversing parking For Truck Van Caravan Trailers Campers IR Night Visoin

Features

Two Night Vision Waterproof Rearview Back Up Reverse Cameras –Auto Water-resistent Camera Lens, with 18 individual Infrared IR LED.  Effective range up to 15m.

2 Cameras 2 Video Inputs–A camera mounted on the front of the car and the second in the back of the car,you can view the back and front of cars

Wired and wireless combination to guarantee safe and stable backup parking system

Color CMOS Camera

Pick-up Device: 1/3 CMOS

TV System: PAL CCIR, NTSC EIA

Scanning System: PAL: 625 Lines; NTSC: 525 Lines, 60 Field

Lens: 2.8 mm Option

Number of Pixels: 500 H x 582 V, 510 H x 492 V

Horizontal Resolution: 420 TV Lines

Scan Frequency: 50 Hz, 60Hz

Electronic Shutter: 1/50 – 1/100 sec 1/60 – 1/100,100 sec

S/N Ratio: >=48dB AGC OFF

Minimun Illumination: 0.8 Lux / F1.2

BLC: Open

White Balance: Auto

Gain Control AGC: Auto

Video Output: 1.0 Vp – p.75 Ω, BNC Connector

Synchronous System: Internal Synchronization

Operation Temperature: -20 Celsius – +80 Celsius

Power Supply: DC 12V – 24V

Focal Distance: 30mm to Infinite

7'' CAR TFT LCD Monitor

Display Size: 7 Inch

Resolution: 480 W x RGB x 234 H

System: PAL & NTSC

Power Supply: DC 9V – 35V

Consumption: 6W

Video: 2 – Channel Video Input, V1 / V2 Switch

Audio: One Way Volume Input

Net Weight: Around 740g

2.4G Wireless Color Video Transmitter and Receiver

Receiver/transmitter frequency: 2400 ~ 2483MHz Transmission Power 10mW / CE 2mW / FCC frequency range 2400 ~ 2483.5MHz

Operating frequency: 2414MHz / 2432MHz / 2450MHz / 2468MHz optional

Power output: 100MW;

Voltage: DC= 9V / 12V;

Video IN/OUT: PAL/NTSC composite video signal

Car closed condition Signal range: 34ft open areas

AV OUT interface: RCA jack

Operating temperature: -10 degrees to +50 degrees

Storage temperature: -30 degrees to +50 degrees

install: The camera is connected with the transmitter, the transmitter from the reversing light mounted on the back or brakes mounted in front connected to 12V power supply. Receiver directly plugged into the cigarette lighter or 12V power connection

Installation instructions

The unit that is labeled 2.4 G wireless color video receivers is the signal receiver. The other unit that is labeled 2.4 G wireless color video is the signal transmitter.

Firstly, you should connect the camera with the transmitter. The yellow interface is for video and the red one is for power. Then connect the wire of the transmitter to the backup light of your vehicle. After theses, mount the camera on your vehicle with two screw s. There are two holes on the case of the camera.

Secondly, connect the extension power cord to the monitor. The red wire and the black wire of the cable is used to connect the 12V/24V power source of the vehicle. The blue one is connected to the back up light. Then connect V1 cable for video with the receiver. The wire of the receiver connects to the reverse circuit in the auto fuse box

Package Include

1 x 7'' TFT LCD Monitor DC 9V-35V

1 x Rearview Camera DC 12V-24V

1 x Mounting Plate

1 x Remote Controller batteries are not included

1 x Signal Rransmitter9V/14V

1 x Signal Receiver9V/14V

1 x Install Instruction

Note

1This monitor can be connected 2 cameras but one of it must be connected by wire and the other one is wireless.
2The AV cable up to 10 meters, easy to install.